R6's s0/0/0 Frame Relay connection line protocol down?

7 posts

3 Dec 2009 at 12:51 a.m. UTC

R6#s run int s0/0/0

interface Serial0/0/0
 no ip address
 encapsulation frame-relay

R6#s frame lmi

LMI Statistics for interface Serial0/0/0 (Frame Relay DTE) LMI TYPE = CISCO
  Invalid Unnumbered info 0             Invalid Prot Disc 0
  Invalid dummy Call Ref 0              Invalid Msg Type 0
  Invalid Status Message 0              Invalid Lock Shift 0
  Invalid Information ID 0              Invalid Report IE Len 0
  Invalid Report Request 0              Invalid Keep IE Len 0
  Num Status Enq. Sent 18               Num Status msgs Rcvd 0
  Num Update Status Rcvd 0              Num Status Timeouts 17
  Last Full Status Req 00:00:06         Last Full Status Rcvd never

R6#s int s0/0/0
Serial0/0/0 is up, line protocol is down 
  Hardware is GT96K Serial
  MTU 1500 bytes, BW 1544 Kbit/sec, DLY 20000 usec, 
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation FRAME-RELAY, loopback not set
  Keepalive set (10 sec)
  CRC checking enabled
  LMI enq sent  19, LMI stat recvd 0, LMI upd recvd 0, DTE LMI down
  LMI enq recvd 0, LMI stat sent  0, LMI upd sent  0
  LMI DLCI 1023  LMI type is CISCO  frame relay DTE
  FR SVC disabled, LAPF state down
  Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface broadcasts 0
  Last input never, output 00:00:09, output hang never
  Last clearing of "show interface" counters 00:03:19
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: weighted fair
  Output queue: 0/1000/64/0 (size/max total/threshold/drops) 
     Conversations  0/5/256 (active/max active/max total)
     Reserved Conversations 0/0 (allocated/max allocated)
     Available Bandwidth 1158 kilobits/sec
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     23 packets output, 301 bytes, 0 underruns
     0 output errors, 0 collisions, 6 interface resets
     0 unknown protocol drops
     0 unknown protocol drops
     0 output buffer failures, 0 output buffers swapped out
     0 carrier transitions
     DCD=up  DSR=up  DTR=up  RTS=up  CTS=up

R6#debug frame lmi

*Dec  3 00:44:42.115: Serial0/0/0(out): StEnq, myseq 1, yourseen 0, DTE down
*Dec  3 00:44:42.115: datagramstart = 0xEEA09AF4, datagramsize = 14
*Dec  3 00:44:42.115: FR encap = 0x00010308
*Dec  3 00:44:42.115: 00 75 95 01 01 00 03 02 01 00

stretch

269 posts

3 Dec 2009 at 3:16 a.m. UTC

I just logged in to poke around and it seems to have fixed itself without any intervention. Not sure what would have caused it but I'll keep an eye on it. Thanks for the report.

Kallisto

7 posts

3 Dec 2009 at 8:06 p.m. UTC

I was working on R6 just now and it was working perfectly. Thanks!

megadeth357

5 posts

6 Dec 2009 at 6:53 a.m. UTC

How can we get the nice copy and past of router command output on here as Kallisto has done above?

When I tried to start a new thread and copy and paste into the forum here from the putty screen I get this....

R1#sho run int ser 0/0/0 Building configuration...

Current configuration : 234 bytes ! interface Serial0/0/0 ip address 10.0.0.1 255.0.0.0 encapsulation frame-relay frame-relay map ip 10.0.0.5 105 broadcast frame-relay map ip 10.0.0.4 103 broadcast frame-relay map ip 10.0.0.1 103 no frame-relay inverse-arp end

Not very good for troubleshooting analysis.

Any suggestions?

Thanks

megadeth357

5 posts

6 Dec 2009 at 7:00 a.m. UTC

And great lab Stretch. Awsome job. Thank you. Strong work.

stretch

269 posts

6 Dec 2009 at 11:38 p.m. UTC

See where it says "For syntax help, see the Editing Guide" below the text field? Probably a good place to look... And thanks!

megadeth357

5 posts

7 Dec 2009 at 12:59 a.m. UTC

R3#ping 10.100.100.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.100.100.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/44/68 ms
Cool thanks! (RTFM)

Kallisto 7 posts	3 Dec 2009 at 12:51 a.m. UTC R6#s run int s0/0/0 interface Serial0/0/0 no ip address encapsulation frame-relay R6#s frame lmi LMI Statistics for interface Serial0/0/0 (Frame Relay DTE) LMI TYPE = CISCO Invalid Unnumbered info 0 Invalid Prot Disc 0 Invalid dummy Call Ref 0 Invalid Msg Type 0 Invalid Status Message 0 Invalid Lock Shift 0 Invalid Information ID 0 Invalid Report IE Len 0 Invalid Report Request 0 Invalid Keep IE Len 0 Num Status Enq. Sent 18 Num Status msgs Rcvd 0 Num Update Status Rcvd 0 Num Status Timeouts 17 Last Full Status Req 00:00:06 Last Full Status Rcvd never R6#s int s0/0/0 Serial0/0/0 is up, line protocol is down Hardware is GT96K Serial MTU 1500 bytes, BW 1544 Kbit/sec, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY, loopback not set Keepalive set (10 sec) CRC checking enabled LMI enq sent 19, LMI stat recvd 0, LMI upd recvd 0, DTE LMI down LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0 LMI DLCI 1023 LMI type is CISCO frame relay DTE FR SVC disabled, LAPF state down Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface broadcasts 0 Last input never, output 00:00:09, output hang never Last clearing of "show interface" counters 00:03:19 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/5/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 1158 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 23 packets output, 301 bytes, 0 underruns 0 output errors, 0 collisions, 6 interface resets 0 unknown protocol drops 0 unknown protocol drops 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up R6#debug frame lmi Dec 3 00:44:42.115: Serial0/0/0(out): StEnq, myseq 1, yourseen 0, DTE down* Dec 3 00:44:42.115: datagramstart = 0xEEA09AF4, datagramsize = 14 Dec 3 00:44:42.115: FR encap = 0x00010308 *Dec 3 00:44:42.115: 00 75 95 01 01 00 03 02 01 00
stretch 269 posts	3 Dec 2009 at 3:16 a.m. UTC I just logged in to poke around and it seems to have fixed itself without any intervention. Not sure what would have caused it but I'll keep an eye on it. Thanks for the report.
Kallisto 7 posts	3 Dec 2009 at 8:06 p.m. UTC I was working on R6 just now and it was working perfectly. Thanks!
megadeth357 5 posts	6 Dec 2009 at 6:53 a.m. UTC How can we get the nice copy and past of router command output on here as Kallisto has done above? When I tried to start a new thread and copy and paste into the forum here from the putty screen I get this.... R1#sho run int ser 0/0/0 Building configuration... Current configuration : 234 bytes ! interface Serial0/0/0 ip address 10.0.0.1 255.0.0.0 encapsulation frame-relay frame-relay map ip 10.0.0.5 105 broadcast frame-relay map ip 10.0.0.4 103 broadcast frame-relay map ip 10.0.0.1 103 no frame-relay inverse-arp end Not very good for troubleshooting analysis. Any suggestions? Thanks
megadeth357 5 posts	6 Dec 2009 at 7:00 a.m. UTC And great lab Stretch. Awsome job. Thank you. Strong work.
stretch 269 posts	6 Dec 2009 at 11:38 p.m. UTC See where it says "For syntax help, see the Editing Guide" below the text field? Probably a good place to look... And thanks!
megadeth357 5 posts	7 Dec 2009 at 12:59 a.m. UTC R3#ping 10.100.100.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.100.100.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/44/68 ms Cool thanks! (RTFM)